Aladdin Quadra-Fire Specifications download pdf (Page 11)

October 10, 2001 11 250-5583

Contour Pellet Stove

MOBILE HOME INSTALLATION

1. Do not install the stove in a sleeping room.

2. The structural integrity of the mobile home oor, walls

and ceiling/roof must be maintained (i.e., do not cut

through oor joists, wall studs, ceiling trusses, etc.).

3. An outside air inlet must be provided for the combustion

air and be unrestricted while the stove is in use. Use

Outside Air Kit (part #811-0871).

4. The combustion air duct system must be made of

metal. It must permit zero clearance to combustible

construction and prevent material from dropping into

the inlet or into the area beneath the dwelling and

contain a rodent screen.

5. The stove must be secured to the mobile home by

bolting it to the oor (using lag bolts).

6. The stove must be grounded with #8 copper grounding

wire or equivalent, terminated at each end with an NEC

approved grounding device.

7. Refer to Clearances to Combustibles Section on page

4 for listings to combustibles and appropriate chimney

systems.

8. Seal all wall and oor inlets to prevent air or moisture

penetration. Check periodically to ensure the inlet is

free of obstruction (e.g., snow, ice).

9. Installation should be in accordance with the Manufac-

tured Home and Safety Standard (HUD), CFR 3280,

Part 24.

THERMOSTAT INSTALLATION

1. A 24 volt AC thermostat is required to operate this

pellet stove and is included. It is equipped with an

adjustable heat anticipator. The current rating is .05

amps. The anticipator needs to be adjusted to the

lowest setting available.

2. When mounting a thermostat on a wall, be sure to follow

your thermostat installation instructions carefully.

NOTE: Be sure the thermostat is mounted level for

accurate readings. The thermostat should be mounted

on an inside wall and not in direct line with the stove

convection air.

NOTE: If the thermostat is located too close to the

stove, you may need to set the temperature setting

slightly higher to maintain the desired temperature in

your home.

There is a four screw terminal block located on the back

of the stove beside the power cord inlet. The center

two screws are for the thermostat wires.

1. FUEL SIZE AND MATERIAL

Wood Pellets

Fuel pellets are made from sawdust or wood by-products.

If the source material is hardwood, they will have a higher

mineral content, creating a heavier ash. Minerals and

other noncombustible materials, such as sand, will turn

into glass when heated to the extreme temperatures our

repot reaches. This is what forms clinkers in the bottom

of the repot. Trees from different areas will vary in mineral

content. That is why some fuels produce more clinkers

than others. Pellets are manufactured in either 1/4” (6mm)

or 5/16” (8mm) diameter and many varying lengths. Pellet

lengths may even vary by lot from the same manufacturer

which is why the feed rate may need to be adjusted

occasionally. We recommend that you buy fuel in multi-

ton lots whenever possible. Buying large quantities of

fuel at once will greatly reduce the number of times the

feed adjustments will need to be made. However, we

do recommend trying various brands before purchasing

multi-ton lots to ensure customer satisfaction.

Shelled Field Corn

Extensive factory and field testing has demonstrated

shelled eld corn to be an efcient and very economical

fuel. We recommend the use of a 50-50 blend of corn

and wood pellets. The only change in operation is that

the feed rate may require a slight adjustment. The BTU

output of the appliance varies slightly compared to pellets,

depending on the quality of the corn used. In cases

where it is acceptable for the stove to run full time,

100% corn will work after the re has been started using

wood pellets.

2. BEFORE YOUR FIRST FIRE

a. First, make sure your stove has been properly installed

and that all safety requirements have been met. Pay

particular attention to the re protection, venting and

thermostat installation instructions.

b. Now open the front door of the stove and remove

all of the accessories that were placed there for

shipment. Remove any labels that may be afxed

to the glass.

c. Check the position of the Thermocouple and make

sure that it protrudes approximately 1” (2.5cm) into the

repot. It may be necessary to slide the Thermocouple

and Thermocouple Cover (ceramic protection tube)

into their proper positions. Now close the front door.

NOTE: Thermocouple Cover tip must be touching

the tip of the Thermocouple.

OPERATING INSTRUCTIONS

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 27 28

Comments to this Manuals

No comments

Aladdin Quadra-Fire Specifications Page 11

Comments to this Manuals